Fulfilling the most demanding requirements in terms of aesthetic appeal
and functionality
The ALW clamping system enables glass facades to be built using special clamps without the need to drill the glass. The slim profile and minimal panel overlap meet the needs of today's architects in terms of both functionality and aestheticallypleasing design.
The holding system is available in standard RAL colours or in anodised versions. This wide choice means that projects can be individually colour-matched.
Up to 18 mm glass
Minimal glass overlapping
No need for drilling glass
Other advantages:
Static analysis and authority approval where required
System constructed from high-quality aluminium
Resistant to weather damage and corrosion
Suitable for other materials such as polymer glass substitute
Both RAL colours and anodised finishes available
Silicone sealing profiles
One-off solutions available where required
The new ALW system enables complete glass facades to be built without the need for drilling glass. The panes of glass are simply slotted into the ALW clamps and fastened into place with the clamping profiles. This newly-developed system can handle glass thicknesses from 8 to 18 mm. In addition to standard and laminated safety glass, alternative materials such as acrylic glass can be readily accommodated.
The ALW clamps can be fixed to a range of sub-frames including steel, aluminium and timber.
Two types are available: the single clamps are 70 mm wide, while the double clamps are 140 mm in width.
Bespoke solutions can also be produced to special order.
Concerning building regulations:
Installation of the ALW system is readily approved following submission of detailed static analysis. This saves time and money. The static analysis is available for reference at any time.
Typical applications:
Facades, double-skin facades
Staircases
Lift shafts
Viewing terraces
Multi-storey car parks and garages
Safety screens
Sun-protection screens
Application single clamp ALW 1 - topview
Application Double clamp ALW 2 - topview
Single clamp ALW 1
Glass tickness:
8 - 18 mm
Glass dimensions:
2000 x 1000 mm*
Deignation:
Single clamp upper for retaining a single pane.
Aluminium with silicone sealing section.
Colour:
RAL - 9006 **
anodised aluminium EV1**
Article number:
529 185
529 189
SFS code:
ALW 1 OBEN
ALW 1 OBEN
Glass tickness:
8 - 18 mm
Glass dimensions:
2000 x 1000 mm*
Deignation:
Single clamp middle for retaining two panes.
Aluminium with silicone sealing section.
Colour:
RAL - 9006 **
anodised aluminium EV1**
Article number:
529 105
529 104
SFS code:
ALW 1 MITTE
ALW 1 MITTE
Glass tickness:
8 - 18 mm
Glass dimensions:
2000 x 1000 mm*
Deignation:
Single clamp lower for retaining a single pane.
Aluminium with silicone sealing section.
Colour:
RAL - 9006 **
anodised aluminium EV1**
Article number:
529 095
529 098
SFS code:
ALW 1 UNTEN
ALW 1 UNTEN
*Dimensions are given as a guide. Static analysis should be carried out for each application. **Other colours available on request.
Double clamp ALW 2
Glass tickness:
8 - 18 mm
Glass dimensions:
2000 x 1000 mm*
Deignation:
Double clamp upper for retaining two panes.
Aluminium with silicone sealing section.
Colour:
RAL - 9006 **
anodised aluminium EV1**
Article number:
529 090
529 092
SFS code:
ALW 2 OBEN
ALW 2 OBEN
Glass tickness:
8 - 18 mm
Glass dimensions:
2000 x 1000 mm*
Deignation:
Double clamp middle for retaining four panes.
Aluminium with silicone sealing section.
Colour:
RAL - 9006 **
anodised aluminium EV1**
Article number:
529 087
529 089
SFS code:
ALW 2 MITTE
ALW 2 MITTE
Glass tickness:
8 - 18 mm
Glass dimensions:
2000 x 1000 mm*
Deignation:
Double clamp lower for retaining two panes.
Aluminium with silicone sealing section.
Colour:
RAL - 9006 **
anodised aluminium EV1**
Article number:
529 081
529 082
SFS code:
ALW 2 UNTEN
ALW 2 UNTEN
*Dimensions are given as a guide. Static analysis should be carried out for each application. **Other colours available on request.
